Cooke & Lewis Freestanding Slimline Dishwasher Recall


Product details: Cooke & Lewis freestanding slimline dishwasher 

For full details, including affected model numbers and manufacturer’s advice, click here.

Reason for recall: Components may overheat, posing a risk of fire

Models Affected: CLDW451W-C / DI6014  Barcode: 5052931055623 Cooke & Lewis white freestanding slimline dishwashers sold by B&Q

What to do next

If you have an affected product please stop using it immediately and unplug.  Call the helpline below for assistance and next steps:

UK: 0300 303 4482 

Helpline hours: Monday to Friday 8.30am–8pm, Saturday 9am–5pm and Sunday 10am–4pm

Read More

Bush Double Oven safety notice

Bush LSBBDFO Double Built In Oven

Argos have issued a safety notice on the Bush branded double built in ovens Model LSBBDFO, following unclear instalation information on page 15 in the guide that accompanies the oven.

The issue relates to how the oven is wired on installation which could lead to overheating and in extreme circumstances can lead to fire.

Argos advise that the Bush branded oven not be used until checked out by there appointed service agents 0800 Repair on 0345 2577271

The affected Models where sold before 10th May 2019

For more recalls and Safety notices click here

Read More

Bush tumble dryer Safety notice

BushFollowing consultation with Milton Keynes Trading Standards, the Bush brand of Tumble Dryer, sold exclusively by Argos have decided to issue additional safety information on the installation, use and maintenance of these affected models:-

Bush Tumble Dryer
Bush TDV6B Tumble Dryer
  • Bush TDV6B 6KG (1288010)
  • Bush TDV6S 6KG (7642966)
  • Bush TDV6B 6KG (1292051)
  • Bush V7SDB 7KG (5386073)
  • Bush TDV6B 6KG (1737901)
  • Bush V7SDB 7KG (5435010)
  • Bush TDV6W 6KG (4810722)
  • Bush V7SDW 7KG (5480948)
  • Bush TDV6W 6KG (7642382)
  • Bush V7SDS 7KG (5496011)
  • Bush TDV6W 6KG (7642399
  • Bush V7SDW 7KG (5586282)
  • Bush TDV6S 6KG (7642959)
  • Bush V6SDW 6KG (4281571)
  • Bush V6SDB 6KG (4287104)
  • Bush V6SDW 6KG (4278041)
  • Bush V6SDS 6KG (4278216)

The main points to remember are as follows: Any restriction in air flow will lead to a potential build up of lint, which in-turn can lead to the lint coming loose and igniting on the heating element.

To prevent this ensure that:

  1. The lint filter found inside the door area must be emptied EVERY TIME the Tumble Dryer is used.
  2. If it is a vented Tumble Dryer that a minimum distance from the wall and the back of the tumble dryer of 10cm (100mm) is left to prevent the vent hose from being crushed.
  3. Also and interestingly not mentioned in the safety notice, If the vent hose is connected to the wall that this vent to the out side is checked and cleaned out at least twice a year.
  4. Do not over load the Tumble Dryer and check fabrics are suitable for the temperature the dryer
  5. Its location, Any tumble dryer should only be installed in a damp free and clean environment. Every dryer sucks in air from its surrounding environment. If there is leaf, pet hair or dust, this will be sucked in and over the heating element, which has the potential to ignite.

Argos can be contacted on 0345 257 7271 or on there web site at

The advice from Argos is relevant for any make and model of Tumble Dryer and by following these simple steps the majority of dryer related fires could be eliminated. Facts about Tumble Dryer Fires

Read More

Register my appliance day

The Institute for White Goods Engineers are very happy in adding our support for Register my appliance day as an essential campaign that will save lives.

AMDEA (The Association of Manufactures of Domestic Appliances) are spear heading this campaign as an important but often missed step in the purchase of a new appliance.

As modern living advances the demand for appliance and white goods has increased, add to this the growing population, then it goes with out saying that we will see a rise in the number of faulty appliances hitting news headlines.

AMDEA members have invested millions of pounds in to developing environmentally friendly technology to greatly improve the efficiency of their appliances.

Technology has advanced from mechanically switched to electronically controlled circuits. This makes them more sensitive to their environment but does add greater control.

  1. an average new European washing machine consumes 44% less energy and 62% less water compared to an average washing machine made in 1985.
  2. in refrigeration, today’s best products consume only a quarter of the energy used by a typical refrigerator  made in 1990.

With more complex products on the market it is inevitable that from time to time faults will surface at component level.

Making the Register my appliance campaign vital.

Consumers lead busy lives and often filling in the registry card or going on line to register an appliance can be the last thing on their mind.

We have long felt that the registration proses should and could be done at the point of sale. In most cases the customers details have already been captured.

A simple API link to submit data to the manufactures portal could elevate the £100,000 spent on urging consumers to register their appliance.

This thought is backed up by a YouGov survey, carried out by AMDEA in December 2016, found that less than half (43%) of GB adults usually register their large domestic appliances, which leaves thousands of owners untraceable if a recall is required.

Electrical Safety First, Trading Standards and the Fire Services, including the 46 fire and rescue authorities across England and the Fire Services in Scotland and Wales all add their support to this campaign.

Registration is simple via this link

Register my appliance day

Once selected scroll to the Manufacture


Read More



Electrical Safety First responds to Government View

Commenting on the Department for Business, Energy and Industrial Strategy (BEIS) response to the investigation into the fridge-freezer model which instigated the Grenfell fire, Phil Buckle, Chief Executive of Electrical Safety First, said:

“We appreciate the thorough investigation undertaken to ensure that this fridge- freezer model fulfils all requirements of the safety standard in place at the time of manufacture. Under these circumstances, no recall of the product has been required.

“However, we are concerned that even the requirement of the current standard means that a significant number of fridge-freezers are still being produced with plastic backs, which can present a fire risk if overheating occurs. Given that faulty white goods alone led to 1,873 fires last year, it is imperative that updated, robust, legislation is established to ensure product safety.

“Electrical Safety First is working with the industry to develop a new voluntary mark. Used by manufacturers of fridges and freezers, it would allow customers to identify appliances that have been made from proven fire-resistant materials.

“We also hope that the recently established Office for Product Safety and Standards will use our expertise to help ensure the UK’s product safety regime works as effectively as possible. But in the meantime, we will continue to lobby for a central recall and registration database to ensure consumers can easily determine if an electrical product they own has been recalled.”

Read More

The Facts around Tumble Dryer Fires

Hotpoint Indesit facia panelsWhirlpool brandsThe Whirlpool, Hotpoint, Indesit and Creda tumble dryer fire story has been a hot topic for many consumer organisations who are pushing for a recall of the affected dryers, rather than the modification that Whirlpool took on when they purchased the brands back in 2014. The affected models potentially numbered into the millions as the safety notice applied to tumble dryers produced between April 2004 – September 2015.

This presented a number of issues:

  1. How to locate all these tumble dryers and are they still in use or have they been scraped.
  2. How to modify them with the current service force.
  3. How to maintain stock levels to facilitate the modifications.

An extensive advertising campaign was launched on tv and in newspapers. Customers that had registered their appliance were contacted first but of course if they have moved that information would be out of date. As owners of the affected models came forward in time they were contacted. There are still many affected models out there that haven’t been reported and the advice of whirlpool not to use them is being ignored.

Whirlpool established a two prong approach to the engineer issue. Quite clearly there would not be sufficient spare capacity with their existing workforce as they would still need to maintain the current service requirements of the business. They began a recruitment and training program for new engineers and also sub contracted to independent engineers around the country.

Whirlpool dryer modification pop rivit

The modification involved removing and replacing the back panel, rear seal and bearing, installing a pop rivet into the rear of the drum and while the drum is removed giving the whole appliance a good clean, removing any build up of lint that may have bypassed the seals. The whole process should take around 45 minutes.

The purpose of the pop rivet is to scrape the rear seal and help prevent any build up of lint as can be seen in the image.  In our opinion due to how little the rivet touches the rear seal lint will still build up.

Whirlpool dryer lint build up on rear seal

This image demonstrates a modified dryer that is still starting to collect lint on the rear seal.

We feel that the modification has not resolved the issue of customer education in the correct use of there dryers.

Also included in this safety notice are some Proline and Swan brands.

Currently Logik, Siemens and Beko also have safety notices in place for some of their models.

Tumble dryers have always been a cause of fires due to a build up of lint igniting on a heater element. We at The Institute for White Goods Engineers feel that;

a. More emphasis needs to be placed on training customers and instalation personnel in the correct use and installation procedures.

b. Also manufactures need to add sensing to check air flow and prompt filter cleaning.

Lint build up occurs mainly when the air flow from the fan, through the clothes, lint filter, condensing chamber (for condensing dryers), vent hose and wall vent are restricted in any way. If there is a restriction pressure builds up in the drum forcing air and lint past the seals.

It is vitally important that:

  1. The lint collector is emptied after every use.
  2. If the dryer is a condensing type, the condensing chamber is removed at least once a month and cleaned.
  3. If it has a vent hose, check that this hasn’t been crushed usually by pushing the tumble dryer back onto it.
  4. Checking the wall mounted vent to the exterior of the building hasn’t become restricted by a build up of lint.
  5. Location also plays a big role, if the dryer is in a location where dust, pet hairs, leaves or anything else can be sucked in, these too can build up and become a potential source of ignition.

The best advice we can provide for our members is, Check for obstructions and remove any build of lint when ever your service engineer opens a dryer for service or repair.

Tumble Dryer lint removal following a serviceAdvise your customers on the use and cleaning that is necessary.

Also a possible solution to the crushed vent hose problem could be to place two 100mm blocks of timber on the floor. This isn’t ideal as will often result in the dryer protruding further than liked, but a house fire is less than ideal also.


4th April 2019

The review, by the Government’s Office for Product Safety and Standards, found that there is a low risk of harm or injury from lint fires in modified machines.

The review explored whether Whirlpool’s technical modification, designed to further reduce the risk of lint fires arising from its tumble dryers, was effective in both design and installation, while also reviewing whether Whirlpool’s consumer outreach programme was adequate.

Read our Press Notice: Review of Whirlpool Tumble Dryer modification finds fire risk is low

12th June 2019

Reports in the media that the Government has ordered a recall of 500,000 tumble dryers under the Whirlpool brand such as Hotpoint, Creda, Proline and Swan.

Currently we can find no supporting evidence that this has taken place and currently as of the above date Whirlpools safety Notice website states the following:-

“Please note that this is not a new campaign and was launched in November 2015. Recent media attention relates to the ongoing campaign. If you have registered for a modification previously then you do not need to register again.

This issue refers only to tumble dryers manufactured between April 2004 and September 2015. Anything manufactured after this date is not affected.

If your tumble dryer has already been modified or you have purchased a replacement machine from ourselves then please be assured that this issue is now resolved for you and no further action is required.”

8th July 2019

A letter from D. Jeffrey Noel, Corporate Vice President of Communications and Public Affairs, Whirlpool to Graham Russell, Chief Executive, Office for Product Safety & Standards

9th July 2019

A reply letter from Graham Russell, Chief Executive, Office for Product Safety & Standards to D. Jeffrey Noel, Corporate Vice President of Communications and Public Affairs, Whirlpool

Which in parts says: I can confirm that OPSS will accept your proposal on the basis set out in your letter of 8 July. To enable us to monitor the recall you must inform us in a timely manner of relevant information, which we will set out.

We expect this action to provide for an effective recall of the unmodified products, such that it would not be considered necessary to issue a recall notice at this time. The acceptance of your proposal does not preclude OPSS from taking enforcement action in the future should there be any reason to reconsider adequacy and effectiveness of the corrective action, including any lack of sufficient and timely progress towards implementation.

10th July 2019

The Department for Business, Energy & Industrial StrategyOffice for Product Safety and Standards, and Kelly Tolhurst MP

Published the following:

Whirlpool UK Appliances Ltd is to issue a product recall of tumble dryers not yet modified from consumers’ homes.

The announcement follows an intervention on 4 June by the government’s Office for Product Safety and Standards (OPSS) which informed Whirlpool of its intent to serve a Recall Notice.

Under the recall, consumers with an unmodified, affected tumble dryer will be entitled to a new replacement machine. This will be delivered and installed, with the old one removed, all at no cost.

Whirlpool has agreed to undertake a number of actions required by OPSS, and which have been reviewed by an Expert Panel, consisting of an independent Queen’s Counsel and 3 Chief Scientific Advisors from the Home Office, Health and Safety Executive and the Department for Business, Energy and Industrial Strategy. These actions are set out in an exchange of letters between OPSS and Whirlpool but include commitments to:

  • deliver a significant new consumer outreach campaign with wide ranging publicity of the product recall aimed at reaching affected consumers and driving up awareness
  • guarantee no charges for delivery, installation or removal of machines
  • improve identification of, and outreach to, vulnerable consumers
  • provide OPSS with timely reporting of progress made in the product recall

Consumer Affairs Minister Kelly Tolhurst said:

The UK has some of the toughest consumer protection laws in the world. Our intervention demonstrates that we will take all the necessary steps to keep consumers safe.

I want to reassure consumers that we are doing everything to ensure consumers with unmodified machines are made aware and have their tumble dryer replaced.

Consumers with an unmodified machine should contact Whirlpool to arrange a free replacement.

The decision follows a review by OPSS, published in April 2019 which instructed Whirlpool to reach affected consumers in more creative ways to minimise the risk of unsafe machines still being in people’s homes. Owners of unmodified, affected tumble dryers should unplug and contact Whirlpool.

Whirlpools product recall/safety notice page remains the same insisting that this relates to the ongoing product recall, and that modified dryers and those that fall out side the date range remain safe to use.

20th July 2019

Jeff Noel, Whirlpool
Jeff Noel, Corporate Vice President of Communications and Public Affairs

Whirlpool issue the following open letter from Jeff Noel, Corporate Vice President of Communications and Public Affairs, Whirlpool on there webpage:

Dear valued customer,

Safety is our top priority and tackling the issue with our tumble dryers has been one of the biggest challenges we have ever faced. We value our customers more than anything and we recognise that we let many of you down. You deserved better from us and for this we apologise to you all.

We are honoured that our brands have been a part of British homes for more than a century and we are immensely proud to still be manufacturing our appliances in the UK. We recognise the huge responsibility we bear and always strive to do the right thing.

We work continuously to build better, safer products and help to drive change that improves safety across the industry.

When we bought Indesit in 2014, we didn’t just acquire a great British company, we welcomed its 5,000 employees and pensioners, and its millions of loyal customers in the UK into the Whirlpool family. With that comes a duty of care for their safety that is of the utmost importance to us.

The safety of Indesit’s tumble dryers was consistent with other brands’ appliances in the market. They met all UK and European regulations too, but Whirlpool demands higher standards, so, we applied our own safety policies to review Indesit’s products. Our review found a potential safety issue in Indesit’s tumble dryers concerning the build-up of lint. It affects certain models made between 2004 and 2015 that were sold under the Indesit, Hotpoint, Creda, Swan and Proline brands.

Even though evaluations under the EU’s official risk assessment system identified this as a low risk issue – its lowest category – we were not satisfied. Shortly after purchasing Indesit, we raised our concerns with the UK regulator and launched a campaign to fix the problem.

We did that because we believed it was the right thing to do to for people’s safety.

We are the first to admit we got some things wrong and could have done some things better. Due to the scale of the challenge, we left many consumers waiting too long and did not provide the level of service we expect of ourselves. That should never have happened and we apologise.

We did everything we could to put that right, hiring thousands of additional engineers and customer advisors to meet demand.

As a result, we have resolved the issue for 1.7 million people. This represents a success rate of up to five times the UK average for a product recall, but we recognise we have more work to do. There may still be people out there with affected dryers who have not responded. It’s vital that we find and resolve those remaining dryers.

To help us achieve that, we are redoubling the efforts of this campaign by issuing a full recall of all unmodified dryers.

That means anyone with an unmodified dryer is entitled to a free replacement, a free modification, a refund based on the age of their appliance, or the opportunity to upgrade to a superior model for a fraction of the retail price.

We’ve worked with the UK Government to agree on these next steps and together we believe this is the right action to encourage any remaining owners of unmodified dryers to come forward.

For anyone who still has an unmodified dryer, please call us immediately on 0800 151 0905 or visit

We thank the millions of people who have already engaged with us; for your time, for your patience, and for your understanding. Nothing matters more to us than your safety and we are truly sorry for any inconvenience caused.

Yours faithfully,

Jeff Noel, Vice President

An interview with Jeff Noel can be found here

Other related documents from the Office for Product Safety can be found here

Read More

Whirlpool AKM 274/IX Gas Hobs

Whirlpool branded stainless steel, built-in gas hobs with the model number AKM 274/IX. The affected appliances were manufactured between September 2014 and March 2016.

The model number can be determined either from the instruction manual or, if access is possible, it will be visible on the rating plate underneath the hob.

If access is not possible then consumers should firstly check if it is constructed from stainless steel material and 60cm wide with four gas burners.

It will also have controls on the right hand side, cast iron pan supports, and a black ignition button in the bottom right corner. Also the Whirlpool logo will be embossed (slightly raised) in the bottom right corner by the control knobs.

Whirlpool state that:

“Due to a technical issue in manufacturing, these appliances were produced with the wrong type of gas injector in the front left corner. The front left burner may emit levels of carbon monoxide above EU standards which could, in very rare usage conditions, present a low risk of adverse health effects through inhalation. There have been no reported incidents involving these products. Investigations have confirmed that the issue does not present a risk of fire or explosion.”

What to do:
The issue concerns the operation of the gas burner in the front left corner of the appliance (Circled in red in the above image).

If you have an affected appliance Whirlpool advises not to use the burner in the front left corner until it has been modified by a Whirlpool engineer.

Whirlpool State that all other burners are unaffected and may continue to be used as normal in the meantime. However, Electrical Safety First always recommends that any recalled product should not be used until it has been checked by the manufacturer.

All consumers who own this appliance should visit:

or contact Whirlpool’s customer care team on:

0800 316 3885

to check if the model number (and serial number) of their appliance is involved in this product safety campaign.

Consumers can select a convenient time for an engineer to visit their home free-of-charge.
Electrical Safety First

Read More

Hotpoint Tumble Dryers – April 2004 – September 2015

Following Whirlpool’s acquisition of the Hotpoint/Indesit brands, Indesit Company has closely reviewed the safety of its product portfolio.

As part of this review we have identified a potential concern with two types of tumble dryers manufactured between April 2004 and September 2015. In some rare cases, excess fluff can come into contact with the heating element and present a risk of fire. The affected brands are:

  • Ariston
  • Hotpoint
  • Indesit
  • Creda

Whirlpool branded tumble dryers are not affected by this safety notice.

We are activating an extensive consumer outreach and service action plan in order to provide our consumers with products that are updated to higher safety and quality standards. We will arrange a visit from an engineer, free of charge, to modify your appliance. The service call will take approximately one hour. The improvements we believe are necessary will further enhance the safety and quality of your dryer.

Trading Standards confirmed, following an internal review by independent experts, that the modification programme remains the most effective way of resolving this issue. As a result, we will continue with our efforts to provide consumers with a free of charge modification as quickly as possible. Trading Standards have also notified us that updated usage advice should be communicated to affected consumers. If your tumble dryer is affected by this issue then you should unplug it and do not use it until the modification has taken place.


Read More

Dealing with Recalls

All electrical products sold in the UK are subject to strict guidelines and testing set out by the British Standards Institute (BSi) this being said when products are put though their paces in domestic or commercial settings issues can surface.

It is then the manufactures responsibility to investigate and where necessary rectify the issue by way of a modification or recall.

As engineers we see these issues often before a safety notice or recall is issued and can therefore play a vital role in reporting potential issues as they arise. Manufactures are a good first point of call but unfortunately it can be hard to get concerns noted.

Electrical Safety First can be contacted and as an organisation the campaigners on electrical safety issues can endeavour to make your concerns heard.

Through their site Safety Notices and Recalls can be searched for and it is worth subscribing for updates as new safety notices or recalls are issued.

As a consumer it is very important that you register your appliance with the manufacture, this is because they will have no way of contacting you if issues arise in the future if you don’t register.

RECALL SEARCH can be done here, scroll down to the yellow boxes and enter the details.



Electrical Safety First offer a service were by you can register with them and they will notify you of any issues that arise with that appliance or electrical product.



Read More